Meridyen Particle Board Screw 6.0X90 (1,000 Pieces)

Meridyen Chipboard Screw 6.0×90 mm — 1,000 Pieces

The Meridyen 6.0×90 mm Chipboard Screw is a specialised fastening solution engineered to deliver maximum depth of hold in the thickest structural components, multi‑layer furniture systems and primary load‑bearing timber construction. With an effective length of 90 mm, it drives through stacked thick sections in a single pass and locks deep into the core; absolutely no sagging, separation or loosening occurs even under the heaviest loads. Supplied in a pack of 1,000 pieces, it provides balanced stock availability for both large‑scale building projects and quality furniture manufacturing.

Technical Specifications

• Brand: Meridyen
• Diameter × Length: 6.0 mm outer diameter, 90 mm working length beneath the head
• Head Type: Reinforced countersunk head; resists breakage or crushing even in hard, thick materials, with a broad seating surface that distributes pressure evenly
• Thread Profile: Reinforced deep‑cut teeth; advances without slipping even in dense chipboard, solid timber and plywood despite high driving resistance, gripping firmly at every stage
• Point Form: Long tapered guide tip; maintains true alignment from initial contact, stays perfectly on axis especially during vertical installation
• Surface Coating: Premium zinc protection; uniform thickness coverage down to thread roots, long‑lasting bright finish
• Pack Contents: 1,000 pieces

Applications

• Multi‑layer panel and beam assemblies with total thickness 60–75 mm
• Base, face and top main structural connections for tall cabinets, wardrobes and storage units
• Thick worktops, table tops and primary frame assembly for heavy seating groups
• Timber roof trusses, main beams and critical load‑bearing joint nodes
• Wall + panel + cavity + load‑bearing beam through‑fixings; heavy furniture anchoring
• Solid wood exterior door frames, large casings and substantial joinery assemblies
• Permanent mounting of high‑capacity shelving, brackets and hanging systems

Product Advantages

• Maximum Depth of Hold: 90 mm length passes fully through the thickest sections and anchors deep in the structural core; completely eliminates risk of layer separation, sag and long‑term loosening
• Multi‑Layer Penetration with One Screw: Clamps stacked panels, insulation and beams together in a single drive; removes weak points and wasted labour caused by using multiple short fixings
• Superior Performance in Dense Materials: Reinforced thread form creates an extensive grip surface even in highly compressed boards; no thread expansion, retains full tightness year after year
• Strong, Crush‑Resistant Head: Reinforced head withstands high torque without fracturing; wide seating face protects the panel surface, leaving a perfectly flush finish after filling and coating
• Practical Pack Quantity: 1,000 pieces provides ample supply for major projects or continuous production; no excessive storage space required, simple stock management
• Stable in Vertical Installation: Long tapered tip resists wandering on ceilings and upright surfaces; drives straight without curving sideways as it advances
• Long‑Lasting Protection: Premium zinc plating stays bright, clean and rust‑free for years in dry, well‑ventilated environments

Installation Guidelines

• Maintain exact 90° alignment; even minor angles multiply driving resistance and may cause the screw to drift sideways
• Add minimum 12–15 mm protrusion beyond the far side; full thread engagement directly determines holding strength
• Minimum edge distance = 20–25 mm; especially critical across the grain or in thick material to prevent splitting
• Drill pilot hole ≈ 60 % of shank diameter; strongly recommended at this length, reduces breakage risk to near zero
• Apply moderate torque only; stop when the head seats flush — over‑tightening crushes the surface and reduces grip
• Avoid direct contact with damp concrete floors in storage; keep on pallets in a dry, ventilated area

Frequently Asked Questions

What does 6.0×90 mm mean and which thicknesses is it best suited for?
6.0 mm is the shank diameter; 90 mm is the effective length measured from beneath the head. It is ideal for total assembly thicknesses of 60–75 mm — perfect for three or four‑layer thick panels, main beam connections or heavy furniture through‑wall fixings.

How does 90 mm length differ from shorter sizes?
Shorter screws grip only the top layer; at 90 mm this passes completely through and locks deep into the lowest structural core. Joints will not sag, loosen or separate under heavy load even after years of use.

Can this screw be used outdoors?
It is manufactured for interior use. Continuous exposure to rain, moisture or direct sunlight may cause rusting over time. For exterior applications select stainless steel or extra‑coated variants.